If you’re getting ready to go on a new garden venture, you need to prepare
your soil to ideally house your plants. The best thing you can do in the
soil preparation process is to reach the perfect mixture of sand, silt,
and clay. Preferably there would be 40 percent sand, 40 percent silt, and
20 percent clay. There are several tests used by experienced gardeners to
tell whether the soil has a good composition. First you can compress it in
your hand. If it doesn’t hold its shape and crumbles without any outside
force, your sand ratio is probably a little high. If you poke the
compressed ball with your finger and it doesn’t fall apart easily, your
soil contains too much clay.

If you’re still not sure about the content of your soil, you can separate
each ingredient by using this simple method. Put a cup or two of dirt into
a jar of water. Shake the water up until the soil is suspended, then let
it set until you see it separate into 3 separate layers. The top layer is
clay, the next is silt, and on the bottom is sand. You should be able to
judge the presence of each component within your dirt, and act accordingly.

After you’ve analyzed the content of your soil, if you decide that it is
low on a certain ingredient then you should definitely do something to fix
it. If dealing with too much silt or sand, it’s best to add some peat moss
or compost. If you’ve got too much clay, add a mixture of peat moss and
sand. The peat moss, when moistens, helps for the new ingredient to
infiltrate the mixture better. If you can’t seem to manage to attain a
proper mixture, just head down to your local gardening store. You should
be able to find some kind of product to aid you.

The water content of the soil is another important thing to consider when
preparing for your garden. If your garden is at the bottom of an incline,
it is most likely going to absorb too much water and drown out the plants.
If this is the case, you should probably elevate your garden a few inches
(4 or 5) over the rest of the ground. This will allow for more drainage
and less saturation.

Adding nutrients to your soil is also a vital part of the process, as most
urban soils have little to no nutrients already in them naturally. One to
two weeks prior to planting, you should add a good amount of fertilizer to
your garden. Mix it in really well and let it sit for a while. Once you
have done this, your soil will be completely ready for whatever seeds you
may plant in it.

Once your seeds are planted, you still want to pay attention to the soil.
The first few weeks, the seeds are desperately using up all the nutrients
around them to sprout into a real plant. If they run out of food, how are
they supposed to grow? About a week after planting, you should add the
same amount of fertilizer that you added before. After this you should
continue to use fertilizer, but not as often. If you add a tiny bit every
couple of weeks, that should be plenty to keep your garden thriving.

Basically, the entire process of soil care can be compressed into just
several steps… ensure the makeup of the soil is satisfactory, make sure
you have proper drainage in your garden, add fertilizer before and after
planting, then add fertilizer regularly after that. Follow these simple
steps, and you’ll have a plethora of healthy plants in no time. And if you
need any more details on an individual step, just go to your local nursery
and enquire there. Most of the employees will be more than happy to give
you advice.

Living in Colorado and being a gardener has been rather stressful in the past few years, as this state has been undergoing a rather severe drought.
The city is imposing watering restrictions which are not giving enough water to lawns and plants. I’ve had to renovate my garden to make it more water efficient. Now, because of the techniques I’ve employed, I’m the only one in my neighborhood with a garden that isn’t completely brown. So if you live in an area that is going through a drought or if you just want to save water, I suggest you use some of these techniques as well.

First, I took out all my plants. The soil I was using didn’t retain water very well, so I had to water about twice as much as necessary in order to get it to actually absorb into the roots. If you have this same problem, you can fix it by loading the soil up with lots of compost. This not only prevents water from escaping, but encourages the plant’s roots to be healthy and able to survive more.

Once I was done optimizing the soil for my new low water consumption plan, I was ready to replace all my plants. I decided that the placement of all my plants would reflect the amount of water necessary to keep them alive.
All the plants that don’t require much water I placed in on one side of my garden, and then just progressed in the amount of required water to the other side of the garden. As a result of my new arrangement, I don’t have to waste water on plants that don’t need it as much.

The installation of a drip irrigation system was another move on my part that reduced the amount of water I needed to fully water my garden. The great thing about these systems is that they constantly drip into your plants, so that every single drop is absorbed. With traditional watering systems, usually the roots get too overwhelmed with the sheer amount of water in the soil. Thus, lots just seeps right past. This is all taken care of with the drip system.
You can learn more about DIY lawn care at our lawn care fertilizing site.